Community : All Content - POD X3

Display has solid black bar on top line and shows Tone2 name below it.

support@line6.com — Sun, 22 Nov 2009 01:23:01 GMT

If you are confident that you can duplicate the problem on your unit within like 5 or 10 minutes then I would consider calling Line6 to see about sending it directly to them to check out. If they can duplicate the problem by following your instructions and they can’t fix it, I bet they would send you another unit. Whenever the X3 series was first released and there were so many problems with it, it wasn’t uncommon for Line6 to have people send their units back so they could see the problem first hand, and they would send a brand new unit to replace it.

Sound Squeak when using pedal as volume or wah

support@line6.com — Sun, 22 Nov 2009 00:18:11 GMT

Reflash Works =D

New x3 live ?

support@line6.com — Sun, 22 Nov 2009 00:12:04 GMT

Good points thanks!! I think an X3 bean will do me just fine though. I am mainly doing recording with my PC. I have a tone port ux1 now that refuses to work streaming audio out at 24 bit with out major noise burst. So I am thinking of upgrading to an X3 hoping it will work better for me.

Harmonizer , Pitch Shifter on pod x3

support@line6.com — Sat, 21 Nov 2009 23:29:53 GMT

boss gt3 had a decent harmonizer on a chipset that is almost 10 year old !

could you at least make a model for the tonecore with exp pedal plug ?

or something similar

Error message installing latest driver for Pod X3

support@line6.com — Sat, 21 Nov 2009 22:48:26 GMT

While you can ignore it, and the installation will complete, Gearbox refuses to communicate with the X3. I guess it's a Snow Leopard compatibility issue.

4 method cable with a Pod X3Live

support@line6.com — Sat, 21 Nov 2009 17:50:28 GMT

Hello

I´ve also tried the 4 cable method solution. I use it in combination with Mesa Boggie Triaxis. Unfortunately there´s a huge hum/noise, especially if I use the high-gain modes of my Triaxis. Is this usual? Any comment on this?

BTW, One more question. What are the recommended settings with regards to the MIX / send / return functionallity of PODs FX loop. Which setting of MIX is parallel respectively serial?

Thanks for comments

Mane

www.pina-coladas.com

Amp for Pod X3

support@line6.com — Sat, 21 Nov 2009 16:25:15 GMT

I use the JBL EON 15G2. I tried various tube amps, solid-state amps with guitar speakers, etc. But I found I wanted 2 things, I wanted total control over my stage volume, I didn't want to count on the sound man to turn my volume up or down in the monitors, and I wanted my tone on the stage to be as close as possible to what was going out of the mains while going direct (not micing my amp). And it has worked out really good. I just did some test a few weeks ago comparing my 100W tube amp with the X3L and another modeler driving the JBL and the modeler/JBL totally kept up with the tube amp in volume, tone and feel, I was surprised how good it sounded. I also tried a 120 watt solid-state poweramp drive a passive monitor and it just didn't have enough power, it sounded good until I tried to keep up with the drums and then it pooped out.

The thing to remember is that it take 2 to 3 times more solid-state power to equal tube power so if you're gonna crank it you'll need plenty of power, personally for a rock band I'd recommend 300 watts minimum. Besides the JBL, I would also look at the Mackie SRM or the new QSC K12.

I haven't tried any keyboard amps myself but I'm sure there are some that sound equally good.

POD x3 pro and sonar 4 producer edition

support@line6.com — Sat, 21 Nov 2009 13:36:49 GMT

You need to monitor the sound from the X3 - not your computer sound card. When you use the POD with a DAW (your Sonar in this case) the POD becomes the soundcard, and all sound being played back is routed to the POD.This is true for monitoring sound while you record as well.

Try plugging headphones into the POD, or connect your speaker system to the POD outputs (headphones or other).

..regarding x3 live effects loop..

support@line6.com — Sat, 21 Nov 2009 11:31:32 GMT

no problem. Have fun and experiment!!!!!!

Using a Boss FV-500H pedal with the X3 Live

support@line6.com — Sat, 21 Nov 2009 08:24:33 GMT

lol, i feel a demotion coming on: http://line6.com/community/message/70969#70969

so the short answer is that if it doesn't work it's time to swap it for another one. sorry